spikecoast5

How to Install a Ghost Immobiliser Ghost immobilisers are hidden security device that protects your car from hacking and key cloning. It prevents the engine of your vehicle from starting until it is started with the PIN code that is as long as 20 characters. This extra layer of protection isn't visible to thieves who are unlikely to be aware of it. Some systems have an app that allows the owner to deactivate their immobiliser if they forget their PIN number or use service/valet mode. Connecting to the vehicle's CAN bus The Ghost 2 Immobiliser is an advanced security system that is able to be integrated into your vehicle's ECU offering a secure protection against thieves. It is highly efficient and user-friendly. This makes it a valuable asset to your vehicle's arsenal of security. Like all anti-theft devices, it's not foolproof, and requires regular maintenance in order to function properly. Luckily, this guide will assist you in getting the most value from the Ghost 2 Immobiliser. CAN (Controller Area Network), a robust serial networking system that lets microcontrollers communicate with each other over short distances. A central control unit is not required. It is designed to multiplex electrical wiring in vehicles, saving on copper. It has numerous advantages including low cost and simple use. In most modern cars, the CAN protocol is used to communicate with various systems, such as the engine management system (EMS), steering module, transmission controller air conditioning controls, and more. It also transmits sensor data like speed sensors and other inputs, to control the various features of the car. The CAN bus is able to monitor the condition of these different components and can stop the vehicle from starting if it is in an unsafe condition. It is important to understand how the CAN bus works and how it's secured. It's possible to add new features to a vehicle using CAN bus, but it's crucial to safeguard it from hackers and other threats. Installing a firewall and monitoring your CAN-bus with software is the best method to accomplish this. Ghost2's control unit is hidden inside the car's dashboard or wiring harness, which prevents an intruder from physically altering it. It's also impossible to reset the PIN or emergency code without access to the vehicle. You can enable Transport Mode If you need to sell your car to valet parking, service or for any other reason. This option disables the Ghost immobiliser's ignition and keyfob functions, and will only reactivate when the car reaches 31 mph for 15 minutes. The process of creating PIN codes The Ghost immobiliser is a powerful security system that guards your vehicle from theft. The patented technology makes use of the PIN to disable the engine of the vehicle and stop it starting without the correct code or an authorized fob or mobile. The system's subtle design is unnoticeable and also provides unbeatable security against theft. The system is TASSA-verified and can save you significant sums on your car insurance. During installation, Ghost enters a “learning mode” to record the sequence of buttons that are that are pressed to generate your unique pin codes. After the pin code is created the installer will guide you through the steps to activate the system. Once activated by the system, the Ghost system will turn off the starter motor of your vehicle until a valid PIN has been entered or the vehicle is switched to transport mode. This makes it very difficult for thieves or cloners who want to hack or duplicate the starter system of your vehicle. Installing a Ghost immobiliser is straightforward, but it is important to follow the specific instructions in the user's guide to ensure proper operation. Multimeters and hand tools can be used to check electrical values. Insulation tape as well as heat shrink tubing and cable ties can be used to protect exposed wiring. Also, make sure to check the system regularly to identify any potential issues and mistakes. It is essential to test the system one more time prior to turning on the ignition. The Ghost immobiliser will arm itself after a period of 3-30 seconds, depending on your vehicle model. The system also comes with a Service/Valet Mode which allows you to temporarily disable the system to service or valet parking. The immobiliser should be placed in a discreet location beneath the steering wheel or on the dashboard. Use ghost immobiliser car of duct tape or paint over the CAN H and L wires to make them easier to find during testing. The CAN H and the L wires should be connected to an electrical source that delivers an uninterrupted 12V. It is also important to re-check the connections after testing, since misidentifying these wires could cause the system to malfunction. Activating the system A ghost immobiliser stops your car from starting unless you press a set of buttons inside the car, usually the steering wheel, door panel, or central console. The sequence is set by the user and can be changed at any time. Once activated, the system can't be turned off. This makes it an ideal choice for anyone looking to protect their vehicle against theft. The system is designed to be undetectable. This means it cannot be detected by modern diagnostics or code-grabbing technology. It also doesn't send radio signals which makes it difficult for thieves to identify the device. If the device is detected, it will stop the engine from starting and sound an alarm with a loud sound to deter thieves. The device can also be used to track the location of the vehicle and help police track it down in the event of theft. Contact Car Specalist Customs for a estimate or to discuss your options in a Ghost immobiliser. We are certified to install ghost immobilisers for your vehicle. We will make sure that it is concealed in a place that is hard to reach. We can also install other security measures, like the kill switch and wheel lock to keep your vehicle safe from thieves. Disarming the System If you own a Ghost immobiliser fitted to your vehicle, it's vital to know how you can disable it. This will aid you in the case that you lock your keys in the car or your battery dies. The system uses an unique PIN code that only you are aware of. It will not start the vehicle without this code. The easiest way to enter the code is to press a set of buttons on your dashboard or steering wheel. This is a far simpler method than using the key fob, and also stops anyone from copying your remote. Ghost2 isn't intrusive, unlike some aftermarket immobilisers which require cutting wires for installation. It also integrates with the CAN bus system of your vehicle to function. Its main characteristic is its ability to bypass the engine without impacting your vehicle's normal functions, making it hard for thieves to make use of signal boosters or copy your car keys. Furthermore, it doesn't emit radio frequencies, which means thieves won't be able to detect it. The Ghost system has a Transport Mode that allows you to temporarily disable security in situations like transportation or service. This feature is great if you are lending your vehicle out to someone else without sharing your PIN number, or if your vehicle needs to be protected even while you drive it. Press the service button five times in 2 seconds to activate Transport Mode. The Ghost system will confirm activation with 5 indication signals. After you're done, make sure to save the emergency code in a secure location outside of your vehicle. If you happen to encounter a situation where you are locked out of your vehicle, contact the technician or company who installed the system, and they'll give you the code. If you are unable to reach them then you can try contacting an authorized dealer however this will require verification procedures and may incur additional costs. In addition to the convenience of this system, you can depend on it to safeguard your vehicle from theft and cut down on insurance costs. Many insurance companies offer lower rates or financial incentives to install this anti-theft system.